CW-5200 Refrigerated Water Chiller for CO2 Laser Machines – 220V AC

LASER PARTS | WATER COOLING & CHILLERS

CW-5200 Refrigerated Water Chiller for CO2 Laser Machines

The CW-5200 is a compressor-based refrigerated water chiller designed to provide actively controlled cooling for water-cooled glass CO2 laser tubes. Unlike radiator-style cooling systems, the CW-5200 can lower coolant temperature below the surrounding room temperature to help maintain consistent operating conditions during engraving and cutting.

With approximately 1,400W of cooling capacity in common configurations, precision temperature control, and built-in alarm protection, the CW-5200 is a practical cooling solution for compatible higher-power CO2 laser machines, longer engraving jobs, and repeated production runs.

Key Features

• Compressor-based refrigerated cooling
• Approximately 1,400W cooling capacity in standard configurations
• Temperature stability rated at ±0.3°C
• Adjustable temperature range from 5°C to 35°C
• Closed-loop water circulation
• Intelligent and constant-temperature control modes
• Digital temperature display and controller
• Integrated coolant reservoir
• Water flow and temperature alarm protection
• Compressor overcurrent protection
• Visible coolant level indicator
• Freestanding design with carrying handles
• 220V AC operating voltage

Product Specifications

Model	CW-5200
Operating Voltage	220V AC
Frequency	50/60 Hz (reference configuration)
Cooling Method	Compressor-Based Refrigeration
Nominal Cooling Capacity	Approx. 1,400W (varies by version)
Temperature Stability	±0.3°C
Temperature Control Range	5°C to 35°C
Temperature Modes	Intelligent / Constant Temperature
Tank Capacity	Approx. 6 Liters (reference configuration)
Pump Power	50W (standard reference configuration)
Maximum Pump Flow	13 L/min (reference configuration)
Maximum Pump Lift	12 m (reference configuration)
Cooling Circuit	Closed-Loop Water Circulation
Protection Features	Flow Alarm, Temperature Alarms, Compressor Overcurrent Protection
Width	11.5 in
Length	22.5 in
Height	19 in (including handles)

Note: Cooling capacity, pump performance, and reservoir capacity are based on published CW-5200 reference configurations. Specifications may vary by manufacturer and model version.

Recommended Applications

The CW-5200 is commonly used with compatible higher-power CO2 laser systems, including:

• 80W and 90W CO2 laser machines
• Compatible 100W and 130W glass CO2 laser tubes
• Laser engraving and cutting machines used for longer production runs
• Applications requiring actively controlled coolant temperatures
• Cooling applications with greater heat loads than basic radiator-cooled systems can manage

The correct chiller should be selected based on laser tube cooling requirements, ambient temperature, expected operating time, coolant flow, and total heat load.

Intelligent Temperature Control

The CW-5200 supports intelligent and constant-temperature control modes. Intelligent mode adjusts the target coolant temperature in relation to surrounding conditions, while constant-temperature mode allows the operator to select a fixed temperature.

Temperature settings should match the laser tube's cooling requirements. Setting coolant temperatures unnecessarily low may cause condensation on the laser tube and coolant lines.

Built-In Equipment Protection

The CW-5200 monitors coolant circulation and temperature during operation. Its built-in alarms help identify problems such as interrupted water flow, excessive or unusually low coolant temperatures, and temperature sensor faults.

When properly connected to a compatible laser machine, the chiller's alarm output can be integrated with the laser protection circuit to help prevent operation when a cooling fault is detected.

Important Operating Information

Always fill the chiller with the coolant recommended for your laser system before operation. Never operate the circulation pump without coolant.

Place the chiller in a clean, dry, well-ventilated area with adequate clearance around the air inlet and exhaust. Regularly inspect the coolant level, tubing, connections, and air filter to maintain proper cooling performance.

Compatibility & Installation

This listing is for the 220V AC version of the CW-5200 refrigerated water chiller. Verify your available electrical service and laser tube cooling requirements before ordering.

Confirm the required coolant flow, hose connections, and compatibility with your laser machine's cooling protection circuit before installation.